Dura-Seal X-TERRA Satin Waterbased Floor Finish Gallon

Dura Seal™ X-TERRA is a two-component, urethane/acrylic resin blend formulated specifically for the demands of commercial and high traffic residential hardwood floors. Its unique technology provides a long- wearing, commercial grade finish that is the ultimate in durability... PRODUCT PROPERTIES:Product Use: New Floors, NaturalSand and prepare...

Dura Seal™ X-TERRA is a two-component, urethane/acrylic resin blend formulated specifically for the demands of commercial and high traffic residential hardwood floors. Its unique technology provides a long- wearing, commercial grade finish that is the ultimate in durability.

PRODUCT PROPERTIES:

• Product Use: New Floors, Natural
• Sand and prepare floor according to NOFMA or NWFA recommended methods.
• Finish sanding with a 120 or 150 grit screen. Do not use steel wool.
• Vacuum thoroughly and tack floor with a slightly water-dampened cloth to remove all dust.
• Apply 1 coat of Dura Seal™ Super Base Sealer
• Apply 2 coats of Dura Seal™ X-Terra.
• For high traffic commercial applications, a third coat is recommended.

• Product Use: New Floors, Stained
• Sand and prepare floor according to NOFMA or NWFA recommended methods.
• Finish sanding with a 100 grit screen. Do not use steel wool.
• Apply Dura Seal™ Penetrating Stain according to label directions.
• Apply 2 coats of Dura Seal™ X-Terra over thoroughly dried stain.
• For high traffic commercial applications, a third coat is recommended.

• Product Use: Previously Finished Floors
• Abrade and Recoat: Be certain floor is free from all wax or oily residue.
• Clean floor thoroughly to remove all contamination.
• Abrade floor with a 120 grit screen. Do not use steel wool.
• Vacuum thoroughly and tack floor with a slightly water-dampened cloth to remove all dust.
• Apply 2 coats of Dura Seal™ X-Terra.
• For high traffic commercial applications, a third coat is recommended.

Note: Do not apply over wax, shellac, lacquer or stains containing wax or stearates.

X-Terra will adhere to most stains and finishes after proper preparation. Always prepare a sample or test area to determine compatibility.

• Product Properties
• Dry Time & Cure Time
• Recoat time: 2-3 hours between coats
• Light foot traffic is acceptable after 24 hours
• Allow one week before exposing finish to rugs, cleaners, spills or heavy traffic
• Coverage: Approximately 350-400 sq.ft. per gallon
• Clean Up: Application tools should be cleaned with warm water immediately after use.
• Maintenance: Use walk-off mats at all entrance doorways to keep dirt and grit to a minimum. Sweep or vacuum daily and damp wipe as needed with Dura Seal™ Hardwood Floor Cleaner.
• Storage: Store at room temperature. If stored at high temperature, cool to room temperature before use. Keep from freezing. If frozen, slowly warm to room temperature and mix thoroughly before using.
• Pot Life: The Finish/Hardener mix must be used within 4 hours after it is mixed. Product properties are diminished after 4 hours. The finish and hardener can only be mixed one time.

DRY TIME & CURE	1) Recoat time: 2-3 hours between coats 2) Wait 24 hours before allowing light traffic 3) Wait one week before replacing rugs and allowing heavy traffic
COVERAGE	Approximately 400-500 sq. ft. per gallon
CLEAN UP	Clean application tools with warm water immediately after use.
MAINTENANCE	Sweep or vacuum regularly to prevent accumulation of abrasive dirt. Do not use all-purpose cleaners. We recommend weekly usage of Dura SeaITM Hardwood Floor Cleaner.
STORAGE	Store at room temperature. Keep from freezing. If frozen, warm to room temperature and mix thoroughly before use.